KTM-4VKF-E
Features
- 3 HP AC-Freq drive head with digital RPM display and analog load meter. Automatic spindle direction reversal when switching between high and low speed gear ranges
- 60-550-4500 spindle RPM (Hi/Low gear)
- Automatic centralized lubrication system with metered check-valves
- Single-phase or 3-phase power without the need for a phase converter
- Hardened and Ground (Hrc-52) table surface and all slide ways
- Solid box ways on saddle and column
Specifications
| Specification | KTM-3VKF | KTM-4VKF-E | KTM-5VKF-E |
|---|---|---|---|
| Table Size | 10" x 50" (10" x 54" Optional) | 12" x 50" | 12" x 50" |
| Table Travel (X-Axis) | 35" | 33" | 33" |
| Saddle Travel (Y-Axis) | 15.25" | 17.5" | 17.5" |
| Knee Travel (Z-Axis) | 15" | 17.5" | 17.5" |
| Quill Travel | 5" | 5.5" | 5.5" |
| Ram Travel | 22" | 22" | 26.75" |
| Spindle Motor | 3 HP | 3 HP | 5 HP |
| Spindle Speed | 50–550–4500 RPM (2-range, Hi/Lo) | 50–550–4500 RPM (2-range, Hi/Lo) | 60–500–4200 RPM (standard variable speed model) |
| Spindle Taper | R-8 | R-8 | NMTB-40 |
| Quill Diameter | 3.375" | 3.375" | 4.173" |
| Quill Feed Rate | 0.0015" / 0.003" / 0.006" in/rev | 0.0015" / 0.003" / 0.006" in/rev | 0.0017" / 0.0032" / 0.0054" in/rev |
| Drilling Capacity (Manual / Power) | 0.75" / 0.37" diameter | 0.75" / 0.37" diameter | 1.25" / 0.625" diameter |
| Boring Capacity | 6" diameter | 6" diameter | 8" diameter |
| Milling Capacity | 2.0 in³/min | 2.0 in³/min | 2.5 in³/min |
| Maximum Work Load (Center) | 850 lbs | 850 lbs | 850 lbs |
| Spindle Center to Column | 5" - 27" | 5" - 27" | 5.25" - 32" |
| Net Weight | 3100 lbs | 3400 lbs | 3700 lbs |
| Gross Weight | 3200 lbs | 3600 lbs | 3800 lbs |
| Shipping Dimensions | 76" x 76" x 88" (skid) | 72" x 72" 100” (skid) | 72" x 72" 88” (skid) |
| Power Requirements | 220 volts, 3 phase, 60 Hz, 10 Amp (optional 440v, requires 5 Amp) | 220 volts, 3 phase, 60 Hz, 10 Amp (optional 440v, requires 5 Amp) | 220 volts, 3 phase, 60 Hz, 17 Amp (optional 440v, requires 8.5 Amp)Can run on single phase power |
Accessories
Optional Accessories
- Digital Readout System (View Brochure)
- Table (X-Axis) Power Feed
- Saddle (Y-Axis) Power Feed
- Knee (Z-Axis) Power Feed
- Air Power Drawbar
- Flood Coolant System
- Chip Pan
- Riser Block
- Angle-Lock Vise
- Rustlick Coolant
