HW-30 Series
Features
- 15 HP spindle motor, 12-speeds
- 4.5″ (115 mm) spindle through hole
- Solid one piece full length casting base and bedways for maximum rigidity
- Spindle jog button control
- One-shot lubrication for apron, multi-position adjustable feed position stops
- Dual inch/metric calibrated tailstock
- Dual inch/metric dials
Specifications
| Specification | HW-26 Series | HW-30 Series | HR-30 Series |
|---|---|---|---|
| Swing Over Bed | 26" | 30" | 30.7" |
| Swing Over Cross Slide | 17.3" | 21.3" | 21.25" |
| Swing Over Gap | 35" | 38.9" | 42.1" |
| Width of Bed | 15.75" | 15.75" | 18" |
| Distance Between Centers | 80" (Opt. 120" / 160") | 80" (Opt. 130" / 169") | 80" (Opt. 120" / 160" / 200") |
| Cross Slide Travel | 14.75" | 14.75" | 15.35" |
| Top Slide Travel | 8" | 8" | 9.4" |
| Spindle Bore | 4.5" | 4.5" | 4" |
| Spindle Speeds | 12 | 12 | 12 |
| Spindle Speed Range | 10-1000 RPM | 10-1000 RPM | 14-1000 RPM |
| Through Hole Diameter | 4.5" | 4.5" | 4.1" (Opt. 6.1") |
| Spindle Nose | D1-11 | D1-11 | D1-11 or A1-11 |
| Spindle Bore Taper | MT#7 | MT#7 | MT#7 - MT#5 |
| Thread – Standard (Whit-worth) | 44 (2-56) TPI | 44 (2-56) TPI | 36 (2-72) TPI |
| Thread – Metric Pitch | 39 (0.5-14) mm | 39 (0.5-14) mm | 65 (0.8-14) mm |
| Longitudinal Feed | 0.002"–0.032" in/rev | 0.002"–0.032" in/rev | 0.002"–0.0276" in/rev |
| Cross Feed | 0.001"–0.0094" | 0.001"–0.0094" | 0.001"–0.00138" |
| Quill Travel | 6.5" | 6.5" | 8.3" |
| Quill Diameter | 3.3" | 3.3" | 4.133" |
| Quill Bore Taper | MT#5 | MT#5 | |
| Main Motor | 15 HP | 15 HP | 20 HP |
| Coolant Pump Motor | 1/8 HP | 1/8 HP | 1/8 HP |
| Packing Dimension | 137" / 186" / 219" x 41" x 52" | 137” / 186” / 219” x 41” x 52” | 151" / 198" / 231" / 270" x 69" x 73" |
| Net Weight | 6570 / 8223 / 10890 lbs | 7010 / 8663 / 11330 lbs | |
| Gross Weight | 6900 / 8554 / 11332 lbs | 7340 / 8994 / 11772 lbs | 9130 - 15400 lbs |
Accessories
Standard Accessories
- 3-jaw chuck (15″)
- Steady rest
- Follow rest
- Thread chasing dial
- 4-position tool post
- 4-position carriage stop
- Coolant system with full-length splash guard
Optional Accessories
- Digital Readout System
- Aloris DA #5-SET (Tool post and 6 holders)
- Royal spindle type live center
- Zero-set 3-jaw chuck with back plate (Zero-set, 15″ D1-11)
- Adaptor plate and rear 12″ 3 jaw chuck for back of spindle
- Face plate (20″ D1-11)
- Taper turning attachment
- Micrometer carriage stop
